/
내 작업대

기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
가입
로그인
세상에서 가장 큰 수리 커뮤니티에 가입하세요.
부품안내서답변
번역하기
Apple Watch Series 2 Display Opening

Apple Watch Series 2 Display Opening

Tobias Isakeit

Tobias Isakeit 및 4 다른 기여자

최종 수정일 June 18, 2024

예상시간 없음
조정
단지 전제 조건
이 안내서는 다른 안내서의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

소개

1단계로 이동하기

Prerequisite-only guide for opening the display for service.

필요한 것

부품

도구

더보기...

  1. Apple Watch Series 2 Display Opening, Power off your Apple Watch: 1 단계, 이미지 2개 중 1개 Apple Watch Series 2 Display Opening, Power off your Apple Watch: 1 단계, 이미지 2개 중 2개
    번역하기

  2. Apple Watch Series 2 Display Opening, Apply heat: 2 단계, 이미지 1개 중 1개

    • Prepare an iOpener (or grab a hair dryer or heat gun) and heat the face of the watch until it's slightly too hot to touch.

    • Leave the iOpener on the watch for at least a minute to fully heat the screen and soften the adhesive holding it to the case.

    • You may need to reheat the iOpener, or move it around on the screen as sections cool, to heat the screen enough to pry it off.

    번역하기

  3. Apple Watch Series 2 Display Opening, Observe all warnings: 3 단계, 이미지 3개 중 1개 Apple Watch Series 2 Display Opening, Observe all warnings: 3 단계, 이미지 3개 중 2개 Apple Watch Series 2 Display Opening, Observe all warnings: 3 단계, 이미지 3개 중 3개
    이 단계에 사용된 도구:
    Safety Glasses
    $3.19
    장바구니에 담기

    • Because the gap between the screen and watch body is so thin, a sharp blade is needed to separate the two. Read the following warnings carefully before proceeding.

    • Protect your fingers by keeping them completely clear of the knife. If in doubt, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.

    • Be careful not to apply too much pressure, as this might cause the knife to slip and cut you, or damage the watch.

    • Wear eye protection. The knife or glass may break, sending pieces flying.

    • Feel free to attach or remove the watch band as needed to provide more control as you make repairs.

    번역하기

  5. Apple Watch Series 2 Display Opening, Pry up the screen: 4 단계, 이미지 3개 중 1개 Apple Watch Series 2 Display Opening, Pry up the screen: 4 단계, 이미지 3개 중 2개 Apple Watch Series 2 Display Opening, Pry up the screen: 4 단계, 이미지 3개 중 3개

    • Place the edge of a curved blade into the thin gap between the display and the outer case. Start at the short side of the display, closest to the digital crown.

    • Press firmly straight down into the gap.

    • Once inserted, tilt the blade to pry the display open slightly.

    • Do not insert the knife more than 1/16th of an inch (~2 mm).

    번역하기

  6. Apple Watch Series 2 Display Opening: 5 단계, 이미지 2개 중 1개 Apple Watch Series 2 Display Opening: 5 단계, 이미지 2개 중 2개

    • Once you've opened a small gap with the curved blade, remove the blade and insert the thinner edge of an opening tool into the gap.

    • Push the opening tool into the gap, using your thumb as a pivot to lift the display open a bit farther.

    • Don't try to fully open or detach the display yet.

    번역하기

  7. Apple Watch Series 2 Display Opening: 6 단계, 이미지 3개 중 1개 Apple Watch Series 2 Display Opening: 6 단계, 이미지 3개 중 2개 Apple Watch Series 2 Display Opening: 6 단계, 이미지 3개 중 3개

    • Insert an opening pick under the display and carefully separate the Force Touch gasket from the display.

    • iFixit screen and battery repair kits include a replacement Force Touch gasket, so don't fret too much if yours is damaged.

    • Otherwise, to preserve the Force Touch gasket, pry carefully under the edge of the display. If the Force Touch gasket splits when lifting the display, or if you separate the gasket layers, you'll also need to replace the Force Touch gasket itself.

    • Slide the pick around the display to separate the adhesive between the Force Touch gasket and the display.

    • Don't insert the opening pick deeper than 1/16th of an inch (~2 mm).

    번역하기

  8. Apple Watch Series 2 Display Opening: 7 단계, 이미지 3개 중 1개 Apple Watch Series 2 Display Opening: 7 단계, 이미지 3개 중 2개 Apple Watch Series 2 Display Opening: 7 단계, 이미지 3개 중 3개
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    장바구니에 담기

    • To avoid straining the display cables, don't open the display all the way yet.

    • Open the display to about a 45° angle, and use tweezers to peel off the adhesive between the display and the Force Touch gasket.

    • Thread the adhesive around and behind the display cables to get it off completely.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

4다른 기여자 명과 함께

Tobias Isakeit

회원 가입일: 03/31/14

124,107 평판

안내서 189개를 작성함

배지: 46

배지 +43개 더

팀

Tobias Isakeit - Repairability Engineer Tobias Isakeit - Repairability Engineer 회원

Business

1 회원

안내서 1,131개를 작성함

댓글 0개

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 6

지난 30일: 19

전체 시간: 259